Новости:

ОЧЕРЕДНАЯ ВСТРЕЧА КЛУБА 10.11.2019 в  11:00
ЖДЕМ ВСЕМ

https://tankspb.com/index.php?topic=1113.0

Автор Тема: CLARK  (Прочитано 3685 раз)

0 Пользователей и 1 Гость просматривают эту тему.

Оффлайн Питерский Танковод

CLARK
« : 24 Ноябрь 2016, 15:03:40 »
TK20 series RC tank Controller
Turn your Heng-Long(HL) RC tank into proportional radio control with decent sound.
THIS IS NOT 100% PLUG AND PLAY BOARD, SIMPLE CHANGE IS NEEDED FOR FULL OPTIONS
(specifications and design are subject to change without notice)
 
100 S
 
[TABLE=width: 640]
Overview
TK20 series controller uses 4 channels RC system to control R/C tank's forward/backward movement, sharp turning, pivoting, turret rotation and gun barrel evaluation at variable speed 20A track motor driver 22KHz, 8-bit high quality sound with digital sound mixer Maximum of 5 channel of sound track, main gun, machine gun, turret rotate, gun barrel elevation and engine sound can be generated at the same time 3W sound output power 0.8A BEC Support air-soft gun with sound synchronization Support TAMIYA and HLIR battle unit and format Support RealRecoil servo port Support gun barrel stabilizer Safety shutoff prevents unwanted movement while signal lost Auto R/C signal detection Miniature design(60mm X 50mm X 20mm) for 1/25~1/16  R/C Tank
 
[TABLE=width: 100%]
Variants
[TABLE=width: 640]
Device
[td=align: center]TK20
[TD=align: center]TK22
[TD=align: center]TK22V
[TD=align: center]TK22G2
[TD=align: center]TK24
[TD=align: center]TK24G2


[TD=align: center]Remote Control System
[TD=align: center]Traditional 4-CH AM, FM or 2.4G RC system
[TD=align: center]Traditional 4-CH AM, FM or 2.4G RC system
[TD=align: center]Traditional 4-CH AM, FM or 2.4G RC system
[TD=align: center]Traditional 4-CH AM, FM or 2.4G RC system
[TD=align: center]Traditional 4-CH AM, FM or 2.4G RC system
[TD=align: center]Traditional 4-CH AM, FM or 2.4G RC system


[TD=align: center]TAMIYA IR battle
Compatible
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]HL IR battle
Compatible
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]VsTank IR
battle
Compatible
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]TAMIYA 1/35 IR battle Compatible
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Damage Simulation
on track
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center] Damage Simulation on turret rotation and gun elevation
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Long range IR battle
(>30M)
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Engine Sound
Simulation
[TD=align: center]Frequency Shift
[TD=align: center]Frequency Shift
[TD=align: center]Frequency Shift
[TD=align: center]Frequency Shift
[TD=align: center] Multi Simple Set,
Fuzzy Logic
[TD=align: center] Multi Simple Set,
Fuzzy Logic


[TD=align: center]Neutral
Gear
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Sound set for
specific tank model
[TD=align: center]3 models
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Track driver
Current
[TD=align: center]20A
[TD=align: center]20A
[TD=align: center]20A
[TD=align: center]20A
[TD=align: center]20A
[TD=align: center]20A


[TD=align: center]Track driver
Momentum Effect
with ON/Off Control
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Turret Rotation Speed Control
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Gun Elevation Speed Control
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Gun Elevation Servo Port
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]AUX Power/Motor Control
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]NO
[TD=align: center]NO


[TD=align: center]2nd MG sound and Light effect
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]NO


[TD=align: center]AirSoft with Sound Synchronization support
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]HL Recoil Unit support
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]NO
[TD=align: center]NO


[TD=align: center]TAMIYA Recoil Unit Support
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]RealRecoil
( Patent Pending)
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Smoker driver
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Proportional Smoker driver
[TD=align: center]No
[TD=align: center]No
[TD=align: center]No
[TD=align: center]No
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Head Light on/off control
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Tank Personalization
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]LED GUN FLASHER Port
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Chassis RecoilOn/Off
Control
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES
[TD=align: center]YES


[TD=align: center]Vertical Gun Barrel Stabilizer
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]NO
[TD=align: center]YES


[TD=align: center]Turret
Heading-Hold
(Horizontal Gun
BarrelStabilizer)
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]NO
[TD=align: center]YES


[TD=align: center]Auto Load Position
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]NO
[TD=align: center]YES


[TD=align: center]Engine Deck Level Detection
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]NO
[TD=align: center]YES
[TD=align: center]NO
[TD=align: center]YES


[TD=align: center]Kit contained
[TD=align: center]TK20 board*1, channel cable*4
[TD=align: center]TK22 board*1, channel cable*4
[TD=align: center]TK22 board*1, channel cable*4
[TD=align: center]TK22G2 board*1,
channel cable*4
GBS unit*1
[TD=align: center]TK24 board*1,
channel cable*4
[TD=align: center]TK24 board*1,
channel cable*4


[TD=align: center]Price
(USD)
[TD=align: center]75
[TD=align: center]90~110
[TD=align: center]90~95
[TD=align: center]249
[TD=align: center]125
[TD=align: center]249


[TD=align: center]Release Schedule
[TD=align: center]EOL
[TD=align: center]Released
[TD=align: center]EOL
[TD=align: center]Released
[TD=align: center]Nov. 2015
[TD=align: center]Nov. 2015


*Horizontal turret stabilizer has motor gain control function which allows user to fine tune performance in different motor and voltage configuration.
*TK22 can be upgraded to TK22G2 or TK24 anytime through our upgrade program.
 
[TABLE=width: 640]
Product Identification System

*Sound set code info is in "Для просмотр ссылок требуется регистрация." page
 
[TABLE=width: 640]
Accessories
[TABLE=width: 640]
Part NumberDescription
[TD=align: center]Configuration IR REMOTE
[TD=align: left]For Tank Personalization function


[TD=align: center]IR005
[TD=align: left]Std. IR battle emitter kit


[TD=align: center]IR010
[TD=align: left]High Power IR battle emitter kit


CAB001
[TD=align: left]1.25mm pitch cable connector for connecting IR LED or Gun Flash LED


HL Cable Set
[TD=align: left]Motor Cable *2
Battery Cable *1
Speaker Cable *1
Smoke Unit Cable *1,
Smoke Unit Switch Cable (no switch) *1
8P Inter-connection Cable *1
Volume Control Cable( no VR ) *1



HL Power Cable
[TD=align: left]One end to TK20, another end to battery, one switch in the middle


IR Programming Line
[TD=align: left]5P connector with IR receiver & Red LED indicator, and  a 2.54mm-pitch Jumper

 


TBU BASE
[TD=align: left]Base and cable to connect TK board to TAMIYA Battle Unit. a 2.54mm-pitch Jumper is included

 


GBS Unit
[TD=align: left]Gun Barrel Stabilizer unit for TK22G1 and TK22G2

 


 
 
 
[TABLE=width: 640]
TK20 ECN( Engineering change notice)
[TABLE=width: 640]
BatchNotice/Change/New FeaturesRelease Schedule
1st-Initial Production
[TD=align: left]Delivered


2nd
-TK20-T and TK20-H are unified as TK-20, Для просмотр ссылок требуется регистрация. function is added for configuration,
-Brightness of battle unit flash is increased,
-Mobility damage simulation function is incorporated,
-Для просмотр ссылок требуется регистрация. and Для просмотр ссылок требуется регистрация. function are added for damage simulation fine tuning,
-LED main gun flasher Port(J3) is added( with cost up by 1 USD) and flash time is also tuned.
-Receive IR code format can be set by Для просмотр ссылок требуется регистрация. and Для просмотр ссылок требуется регистрация.
-New T-55 sound version is available,
-IR battle preset data for HL is corrected,
-Save current setting to PRESET 3 function is removed.
Delivered


2013 production
- No software change to TK20,
- Formal TK22 production run,
-TK22-M41 will be released with this batch.
-Price is increase a little bit due to USD exchange rate, labor and material cost. Preorder is not affected.
Delivered


2014 production
- No software & Hardware change
Delivered


2015 production
- No software & Hardware change
Delivered


2016 production
- No software & Hardware change for TK22
- TK24 added
Dec.2015







   
 
[TABLE=width: 640]
TK20/TK22/TK22G2 Control Mode and operation
[TABLE=width: 640]
Engine sound on/off
Cannon elevation
Booming Cannon
(For TK20/TK22/TK22V)
Booming Cannon
(For TK22G2)
Gun Barrel Stabilizer on/off
(For TK22G2)
Fire MG: Number of burst is controlled by the time of stay.
Head light control on/off
AUX Power on/off (Only available when Main Gun Function Mode is set to Gun elevation servo Mode)
Tank move forward and backward
Right and  Left turn
Turret rotation
     
[TABLE=width: 100%]
TK24/TK24G2 Control Mode and operation
[TABLE=width: 640]
Booming Cannon
TK24: Fire MG2 (Servo Elevation Mode)
TK24G2: Gun Barrel Stabilizer on/off
Cannon elevation
Turret rotation
Neutral Gear Shift In/Out :
Track motor does not move when shift to natural gear
Engine sound on/off
Fire MG: Number of burst is controlled by the time of stay.
Head light control on/off
Tank move forward and backward
Right and  Left turn
 
[TABLE=width: 640]
Specification
[TABLE=width: 100%]
ParameterUnit
Maximum current of track ESC20A
Maximum current of turret and cannon elevation ESC6A
Maximum current of Smoker Driver6A
Maximum supply voltage7.4V
Minimum supply voltage7.2V

TK20 series connector layout


   
TK20/TK22/TK22V/TK24 connector and pin assignments(Text in red is the modification required for HL TANK)
[TABLE=width: 640]
ConnectorDescription
[TD=align: left]Main Gun Function Mode is set to Gun elevation servo Mode
[TD=align: left]-H version, or Main Gun Function Modeis configured to AirSoft or HL Recoil
[TD=align: left]-T version, or Main Gun Function Mode is configured to TAMIYA Recoil


SW
Switch Cable Port
[TD=colspan: 3, align: left]HL tank already have power switch on battery cable path, so additional  switch is no longer required, just to short pins in this port by jumper or connect to a switch cable and keep it switched on.

 


CN1
Battery Power
[TD=colspan: 3, align: left]1. Battery +
2. Battery -


CN2
Infrared Port
[TD=colspan: 3, align: left]1. HBU/TBU +
2. HBU/TBU SIG
3. HBU/TBU -
4. TBU FLASH LED -
5. TBU FLASH LED +


CN3
Gun FlashPort
[TD=align: left]1. Battery +
2. Strobe Trigger
3. Battery -
4. Not Used
5. Not Used
[TD=align: left]1. Battery +
2. Strobe Trigger
3. Battery -
4. AirSoft/Recoil Switch
5. AirSoft/Recoil Switch
[TD=align: left]1. Battery +
2. Strobe Trigger
3. Battery -
4. TAMIYA Recoil Unit Switch
5. TAMIYA Recoil Unit Switch


CN4
Sound Volume
[TD=colspan: 3, align: left]1. Volume Signal Output ( Wiper pin of VR )
2. Battery -( 1 outside pin of VR )
3. Volume Signal Input ( 1 outside pin of VR )


 


CN5
Speaker
[TD=colspan: 3, align: left]1. Speaker -
2. Speaker +


CN6
Motor Left
[TD=colspan: 3, align: left]


CN7
Motor Right
[TD=colspan: 3, align: left]


CH1
Steeringcontrol signal
[TD=colspan: 3, align: left]Futaba: CH1
JR:AILE


CH2
Throttlecontrolsignal
[TD=colspan: 3, align: left]Futaba: CH2( Mode 2)  or CH3 ( Mode 1 )
JR:ELEV


CH3
Multi functioncontrol signal 1
[TD=colspan: 3, align: left]Futaba: CH3( Mode 2) or CH2 ( Mode 1 )
JR:THRO


CH4
Multi functioncontrol signal 2
[TD=colspan: 3, align: left]Futaba: CH4
JR:RUOD


CN9
Upper Hull Functions
( Turn, Lift, Shoot, Light)
[TD=align: left]1. Machine gun LED-
2. Head Light LED-
3. Machine gun LED+,
    Head Light LED+,
    AUX Power+,
    MG2 Light LED+
4. AUX Power-
    MG2 Light LED-
5. GUN ELEVATE MOTOR
6. GUN ELEVATE MOTOR
7. TURRET MOTOR
8. TURRET MOTOR
[TD=align: left]1. Machine gun LED-
2. Head Light LED-
3. Machine gun LED+,
    Head Light LED+ &
    AIRSOFT/RECOIL 
    Motor+
4. AIRSOFT/RECOIL Motor-
5. GUN ELEVATE MOTOR
6. GUN ELEVATE MOTOR
7. TURRET MOTOR
8. TURRET MOTOR
[TD=align: left]1. Machine gun LED-
2. Head Light LED-
3. Machine gun LED+,
    Head Light LED+ &
   TAMIYA Recoil unit
   green Wire
4. TAMIYA Recoil unit white Wire
5. GUN ELEVATE MOTOR
6. GUN ELEVATE MOTOR
7. TURRET MOTOR
8. TURRET MOTOR


CN10
Smoke Unit
[TD=colspan: 3, align: left]


CN11
Smoke Unit Switch
[TD=colspan: 3, align: left]


J1
IR Battle Emitter Port
[TD=colspan: 3, align: left]To work with IR battle emitter(IR010)
1. IR LED +
2. IR LED -


J2
RealRecoilServo  Port
[TD=colspan: 3, align: left]RealRecoil Servo Port is always turned ON, no setting is needed to turn it on
1. Signal( White Wire)
2. +5V ( Red Wire)
3. Battery - (Black Wire)

See RealRecoil section in Assembly Guide


J3
LED Main Gun Flasher Port
[TD=colspan: 3, align: left]1. Main Gun  LED +
2. Main Gun  LED -


J4
Gun Elevation Servo
Port
[TD=align: left]1. Signal
( White Wire)
2. +5V
( Red Wire )
3. Battery -
(Black Wire)
[TD=colspan: 2, align: left] Not used
 


J5
NA
[TD=colspan: 3, align: left]NA



   
TK22G2/TK24G2 connector and pin assignments
[TABLE=width: 640]
ConnectorDescription
[TD=colspan: 2, align: left]Pin assignments


SW
Switch Cable Port
[TD=colspan: 2, align: left]HL tank already have power switch on battery cable path, so additional  switch is no longer required, just to short pins in this port by jumper or connect to a switch cable and keep it switched on.

 


CN1
Battery Power
[TD=colspan: 2, align: left]1. Battery +
2. Battery -


CN2
Infrared Port
[TD=colspan: 2, align: left]1. HBU/TBU +
2. HBU/TBU SIG
3. HBU/TBU -
4. TBU FLASH LED -
5. TBU FLASH LED +


CN3
Gun FlashPort
[TD=colspan: 2, align: left]1. Battery +
2. Strobe Trigger
3. Battery -
4. Not Used
5. Not Used


CN4
Sound Volume
[TD=colspan: 2, align: left]1. Volume Signal Output ( Wiper pin of VR )
2. Battery -( 1 outside pin of VR )
3. Volume Signal Input ( 1 outside pin of VR )


 


CN5
Speaker
[TD=colspan: 2, align: left]1. Speaker -
2. Speaker +


CN6
Motor Left
[TD=colspan: 2, align: left]


CN7
Motor Right
[TD=colspan: 2, align: left]


CH1
Steeringcontrol signal
[TD=colspan: 2, align: left]Futaba: CH1
JR:AILE


CH2
Throttlecontrolsignal
[TD=colspan: 2, align: left]Futaba: CH2( Mode 2)  or CH3 ( Mode 1 )
JR:ELEV


CH3
Multi functioncontrol signal 1
[TD=colspan: 2, align: left]Futaba: CH3( Mode 2) or CH2 ( Mode 1 )
JR:THRO


CH4
Multi functioncontrol signal 2
[TD=colspan: 2, align: left]Futaba: CH4                     
JR:RUOD


CN9
Upper Hull Functions
( Turn, Lift, Shoot, Light)
[TD=colspan: 2, align: left]1. Machine gun LED-
2. Head Light LED-
3. Machine gun LED+, Head Light LED+, GBS LED+
4.  GBS LED -
5. GUN ELEVATE MOTOR
6. GUN ELEVATE MOTOR
7. TURRET MOTOR
8. TURRET MOTOR


CN10
Smoke Unit
[TD=colspan: 2, align: left]*NOT available


CN11
Smoke Unit Switch
[TD=colspan: 2, align: left]*NOT available


J1
IR Battle Emitter Port
[TD=colspan: 2, align: left]To work with IR battle emitter(IR010)
1. IR LED +
2. IR LED -


J2
RealRecoilServo  Port
[TD=colspan: 2, align: left]RealRecoil Servo Port is always turned ON, no setting is needed to turn it on
1. Signal( White Wire)
2. +5V ( Red Wire)
3. Battery - (Black Wire)

See RealRecoil section in Assembly Guide


J3
LED Main Gun Flasher Port
[TD=colspan: 2, align: left]To Work with LED Main Gun Flasher(F003)
1. LED +
2. LED -


J4
Gun Elevation Servo
Port
[TD=align: left]1. Signal( White Wire)
2. +5V ( Red Wire )
3. Battery - (Black Wire)
[TD=align: left]Not Used


J5
Engine Deck Level Switch Port
[TD=colspan: 2, align: left]1. SWITCH
2. SWITCH
3. NO CONNECTION.
* To close Pin1 and Pin2 when gun barrel travels above engine deck


J6
GBS Unit Port
[TD=colspan: 2, align: left]To connect GBS (Gun Barrel Stabilizer) unit


 
 
[TABLE=width: 100%]
Assembly Guide
Inspect metal portion on FETs and make sure they are not touched to each other after shipment

Set Для просмотр ссылок требуется регистрация. to match your tank hardware configuration (HL AirSoft, HL Recoil or TAMIYA Recoil),
Disconnect RX-18 and plug cables to the same connector on TK board,
Set Sound Volume to middle
Install a switch cable (for example, HL Smoke Unit Switch Cable) to SW connector( Switch Cable Port)  as power switch.
 
Because HL tank already have power switch on battery cable path, so additional switch is not required, just to use a jumper to short pins in SW Cable port or connect a switch cable and keep it switched on.

 
When high current track motors are used, such as 400/480 motor, power switch on battery cable path will not be able to handle, connect a switch cable (for example, HL Smoke Unit Switch Cable) to this port as power switch.
Connect a recoil servo to J2(Optional),
Rewire Air-soft unit if you want to elevate and depress gun directly, see "Для просмотр ссылок требуется регистрация." section
Connect channel cables to receiver according to RC mode( See picture "TK series connector and pin assignments" ) . if you are not sure what mode you RC system is, just swap CH2 and CH3 and try again.
 
When use F-4 Radio, connect receiver CH1~CH4 to TK20 CH1~CH4, Set transmitter control mode to mode 1, all reverser to REV position
 

 
TK20 board has BEC( Battery eliminate circuit), can power receiver through channel cables, no additional battery is needed for receiver
 
Set CH1, 2 and 3 trimmer on transmitter to center position, Set CH4 trimmer on transmitter to most left or right  position,
Connect power adaptor( See FAQ )
Switch on TK board and transmitter, you should hear turret traverse sound. if not, please contact us.
gently move CH4(Multi function control signal 2) trimmer to center till turret traverse is gone.
gently move CH2(Throttle ) trimmer up and down if you hear motor hum sound.
Cannon firing sound should be generated and recoil servo should moves when move CH3 stick to most top position, if not, gently move CH3(Multi function control signal 2 ) trimmer up and down till it work correctly.
You are all set
Disconnect power adaptor and connect battery( make sure that battery is fully charged).
 
 
[TABLE=width: 640]
HL Gun Elevation and AirSoft Correction
In HL original design, gun Elevation and AirSoft sharing same driving H/W, so the gun elevation can only be controlled  in one direction, if you missed the angle you want, you will need to wait a full cycle of gun elevation, to correct this problem, we add dedicate AirSoft control h/w to TK20 board. the following shows you how to correct HL tank and get two direction elevation.
 
The picture below is original wiring in HL tank:

Modify it as the following:

Green box in the diagram above represent the small PCB in tank, small  red, black, blue ... orange in it represent the wire color.

1. Disconnect red wire between safety switch and gun barrel elevation unit.

2. Change original 3P connector to 4P type, add additional wire from safety switch to 4P connector,

3. Add 4P connector HUL-8P PCB connector

4. AirSoft unit is now controlled by red-black pair, gun barrel unit is controlled by red-white pair. and you can connect 8P connector to CN9 on TK-18/20 with original cable.

5(Optinal). refer to wiring diagram, wire a 2.2 ohm 1/2W (color code: red read gold gold) in-serial resistor to turret rotate, elevation and airsoft motor to limit the current to protect FETs on TK22 in case you stall motor.

2.2 ohm resistor can also be found on RX-18.

Here is a video of airsoft setup for Taigen Tank

 
[TABLE=width: 640]
HL Tail Light Correction
Tail Light in HL tank is wire to MG light, so the Tail Light flashes when MG firing, this is very funny to us, to correct this problem and make tail light to be controlled with Headlight, please refer to the picture below and rewire it.
1. Remove 2 pin plug from PCB, twist angled pins to opposite side,
2. Connect Tail Light LED + pin(  Red wire of Tail Light cable) to CN9.3 pin( Yellow wire )
3. Connect a 200 Ohm resistor between 2-P connector pin and CN9.2 pin(Green), a SMD type resistor is used in this example to save space.
 

Original wiring diagram

Corrected wiring diagram

 
[TABLE=width: 100%]
Battle unit installation
TAMIYA battle unit wiring diagram

HL battle unit installation: wire CN2 connector to HBU and  Flash Unit Flasher as the following

 
[TABLE=width: 100%]
Recoil Unit Installation
TAMIYA recoil unit installation( -T Version, or set Main Gun Function Mode to TAMIYA Recoil MODE )
STEP1. disconnect white and blue wire from recoil unit switch( see arrow in yellow), add cable connector to recoil switch( see arrow in red ), left green-white-blue cable not touched ( see arrow in green)

STEP2. green wire and white wire in green-white-blue cable goes to 3rd pin on CN9 and 4th pin on CN9(see arrow in green), black and red wire in red-black cable goes to 4th and 5th pin on CN3(see arrow in red).

 

 
HL recoil unit installation:
STEP1. Set Main Gun Function Mode to HL Recoil MODE,
STEP2. Connect detection SW( Pressed-to-Short type ) to 4th and 5th pin on CN3 or via the plug (Yellow and brown wire) from  HL HIGH-TENSION FLASHER. Latest released HL recoil unit already has detection switch on it.


STEP3. connect motor - to 4th pin on CN9.connect motor + to 3rd pin on CN9.

Asiatam recoil unit installation:
STEP1. Set Main Gun Function Mode to TAMIYA Recoil MODE,
STEP2. Connect  Recoil motor + to 3rd pin on CN9.connect motor - to 4th  pin on CN9.

STEP2. Connect detection SW to 4th and 5th pin on CN3 or via  the plug (Yellow and brown wire) from  HL HIGH-TENSION FLASHER

 

 

 
RealRecoil( Patent Pending) servo port allows you to recreate real gun barrel recoil movement with single &  cheap servo, what you need to do is to link servo and gun barrel then RealRecoil takes the rest. direction of servo movement can be set by user, please see section "Tank Personalization"


 

 
[TABLE=width: 100%]
GUN FLASHER Installation
HL Hop-up options "HIGH-TENSION FLASHER" can be easily installed and works with TK20 to simulate gun nuzzle flash when firing.

 
[TABLE=width: 100%]
LED GUN FLASHER Installation:
A white LED and cable connector are needed( Part Number is F003)

Solder color wire (red wire in this example) to long pin of white LED, black wire(-) to short pin,

Plug cable into J3.

 
[TABLE=width: 100%]
IR battle emitter Installation
An IR  LED and cable connector are needed( Part number is IR005/IR010 ).

Solder color wire (red wire in this example) to long pin of IR LED, black wire(-) to short pin,

Plug cable into J1.

 
 
[TABLE=width: 100%]
Gun Barrel Stabilizer(GBS) overview and installation
GSU is an optional module of TK22. When GSU is turned on, it detects the tank movement and compensategun rotation and elevation to stabilize the gun automatically. When GBS is turned on, operator can still change gun elevation and direction under GBS compensation, GSU have the following features:
 
- 2-axis gun stabilization in turret rotation and gun elevation.
- Fully programmable gun elevation real angle calculator allows GBS to work with different elevation setup,
- Fully programmable turret motor controller allows GBS to work with different motor/gear box setup,
- Engine deck detection, gun raise automatically when gun travels above engine deck,
- Auto reload position, Gun barrel goes to to reload position after fire, and return to last position when reload when reload time expired,
- Adjustable Engine deck level,
- Adjustable auto reload position,
-  GBS unit dimensions: 20 x 16 x 3mm.
- Unified platform design, allows all existing TK20/TK22 can be shipped back to us to upgrade to TK22G2
 
Servo for GBS -
-Control System: +Pulse Width Control 1520usec Neutral
-Required Pulse: 3-5 Volt Peak to Peak Square Wave
-Operating Voltage: 4.8-6.0 Volts
-Operating Angle: 45 Deg. one side
Power on GBS calibration - When power on TK22G2, GSU starts a reset process and must be kept stationary.
The GBS LED blinks during GBS calibration and you must not to  move the tank during calibration.The GBS are very sensitive and you should not touch or vibrate the GSU during power on reset. The process will take a few seconds. The HEADLIGHT led will turn on when calibration completed.
An in-series 200-ohm resistor is needed for GBS LED

 
Mounting of GBS - The GBS unit must be mounted securely and horizontally on the turret, here is an example, first to use Tamiya 5mm square beam, cut into 5~6mm in length, make 1.6mm hole, then glue to turret floor by cement

Bolt GBS unit with the screws came with GBS unit, and plug connector to J6 port on TK22G2, Length of GBS cable can not exceed 80mm or TK22G2 may miss reading GBS.

For accurate motion detection, it must be kept within 5 degree with turret base plate. mounting directions is as shown in following picture. Servo for elevation is Futaba S3003 in this setup.

Recommended GBS mounting position for Leopard 2

 
Turning GBS on/off - GBS can be turned on/off by move right stick to top, move left stick to right, you can also hear click sound when turn it on and off

Adjusting gun elevation angle - The gun elevation V gain setting is used to adjust the amount of gun elevation servo angle to meet different mechanical setup. adjusting procedures are
 
-First to put TK22G board in IR programming mode.
-Turn GBS on and moves the gun barrel to horizontal position.
-Tilt the tank for 15-20 degree.
-Use IR configure remote to adjust servo gain value until the gun is horizontal again.
-Power off TK22G board, remove jumper and turn power again to leave IR programming mode.
 
Adjusting gun elevation angle calculator gains - The angle calculator's fast gain and slow gain settingsare used to adjust the angle calculation, adjusting procedures are
 
-First to put TK22G board in IR programming mode.
-Turn GSU on and moves the gun barrel to horizontal position.
-Tilt the tank for 10-20 degree.
-Rotate turret in various speed ( from low to full speed), if elevation speed is too slow, increase slow gain a bit, otherwise, reduce slow gain,
-rotate turret to 12 o'clock position, tilt the tank hull about 15-20 degree in various speed, if elevation speed is too slow, can not keep up tank hull tilt speed, increase fast gain a bit, if elevation moves faster the hull tile speed and over the position it should be (overshoot), decrease fast gain a bit
-Power off TK22G board, remove jumper and turn power again to leave IR programming mode.
 
Adjusting turret rotation motor control gains -Turret rotation motor P , I  and D gain are used to meet the characteristic of turret rotate motor and design on your tank. adjusting procedures are as the following.
 
-First to put TK2xG2 board in IR programming mode.
-Turn GSU on
-Rotate tank hull from stationary to low speed, if turret motor does not start as quick as tank hull rotation, increase I gain a bit, if turret motor runs too fast (overshoot) , decrease I gain a bit.
-Rotate tank hull in various speed( low, middle and full) , if turret rotation speed is too slow, can't keep up hull rotation, increase P gain, otherwise, reduce speed gain,
-Stop tank hull rotation from various speed, if turret stops too early, decrease D gain, if turret stops too late increase D gain.
 
[TABLE=width: 100%]
Tank Personalization( Patent Pending)
Settings of TK series board can be changed by Configuration IR REMOTE as IR command transmitter, and TAMIYA battle unit(TBU),  Heng-Leog battle unit(HBU), or our programming line as IR command receiver.
 

Steps to change settings:
STEP 1: Turn power off, Turn power off, Turn power off,
STEP 2: Plug programming line/TBU/HBU through TBU/HBU base into CN2 Infrared Port , 

STEP 2: Install a jumper to J2 as shown below, Turn power on,

STEP 4:Refer to function table listed below, point Configuration IR REMOTE to TBU/HBU/Programming line receiver, and press the button of setting that you want to change,  "*" sign in function table means the default setting that is programmed in factory

STEP 5: Indicator on TBU/HBU flashes according to new setting value.
STEP 6: turn power off, remove jumper on J2, then turn power on and TK board runs with new settings.
 
Type of Tank determines Battle Date when doing IR battle( See Variants section )
[TABLE=width: 100%]
[TD=align: center]Type of Tank
[TD=colspan: 3, align: center]Tank Mobility, Turret rotation and Gun barrel evaluation speed
vs.
Hit taken


[TD=align: center]Damaged
State
[TD=align: center]Badly Damaged
State
[TD=align: center]Destroyed
State


[TD=align: center]Heavy Tank*
[TD=align: center]1~4 hits taken
[TD=align: center]5~8 hits taken
[TD=align: center]9 hits taken


[TD=align: center]Medium Tank
[TD=align: center]1~3 hits taken
[TD=align: center]4~5 hits taken
[TD=align: center]6 hits taken


[TD=align: center] Light Tank
[TD=align: center]1 hit taken
[TD=align: center]2 hits taken
[TD=align: center]3 hits taken


[TD=align: center]HL Tank
[TD=align: center]1~2 hits taken
(Note)
[TD=align: center]3~4 hits taken
(Note)
[TD=align: center]5 hits taken


Note: HENG-LONG TANK doesn't have Damaged State and Badly Damaged State. speed reduction can be turned off by Для просмотр ссылок требуется регистрация. and Для просмотр ссылок требуется регистрация. function.
 
[TABLE=width: 100%]
[TD=align: center]Type of Tank
[TD=align: center]Reload Time
[TD=align: center]Recovery Time
[TD=align: center]Invulnerability time


[TD=align: center]Heavy Tank*
[TD=align: center]9 sec.
[TD=align: center]15 sec.
[TD=align: center]10 sec.


[TD=align: center]Medium Tank
[TD=align: center]5 sec.
[TD=align: center]15 sec.
[TD=align: center]12 sec.


[TD=align: center] Light Tank
[TD=align: center]3 sec.
[TD=align: center]15 sec.
[TD=align: center]15 sec.


[TD=align: center]HL Tank
[TD=align: center]3 sec.(Note)
[TD=align: center]15 sec.
[TD=align: center]10 sec.(Note)


Note: Suggested Value, can be changed by Reload Time and Invulnerability time setting function
 
Function tables:
Save current setting to PRESET 1: Press number key "1" on IR Configuration Remote to save,
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Save to PRESET 1
[TD=align: center]1
[TD=align: center]Indicator flashes when setting is saved


 
Save current setting to PRESET 2: Press number key "2" on IR Configuration Remote to save,
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Save to PRESET 2
[TD=align: center]2
[TD=align: center]Indicator flashes when setting is saved


*Once you've adjusted everything, you can push "1" or "2" to save current setting to PRESET 1 or 2. If you don't do this saving the board remembers the last settings.
 
Use saved settings: Press "ENT" or "SOUND MODE" Key on IR Configuration Remote to select.
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Use PRESET 1 setting
[TD=align: center]1
[TD=align: center]


[TD=align: center]Use PRESET 2 setting
[TD=align: center]2
[TD=align: center]


[TD=align: center]Use Factory Default Setting
( Read-Only )
[TD=align: center]3
[TD=align: center]To restore factory default value in case of setting data is messed up.


*To switch between the presets you press either "sound mode" or "enter" button, once the preset is selected, switch tank off and remove setup jumper. Switch back on and away you go.
 
Mixer Mode: Press (MUTE) key on IR Configuration Remote to select.
[TABLE=width: 640]
[TD=align: center]Available Settings
[TD=align: center]Indicator flashes times
[TD=align: center]Description


[TD=align: center]Mixer Mode 1
[TD=align: center]1*
[TD=align: center]Tank mode 1
CH1 controls rudder, CH2 controls throttle.
Proportional steering, sharp and pivot turn* are supported
[TABLE=width: 99%]
[TD=colspan: 3, align: center]Left Track
[TD=colspan: 3, align: center]Right Track


[TD=align: center]Pivot
Turn
[TD=align: center]Sharp
Turn
[TD=align: center]Proportional
Steering
[TD=align: center]Proportional
Steering
[TD=align: center]Sharp
Turn
[TD=align: center]Pivot
Turn


 


[TD=align: center]Mixer Mode 2
[TD=align: center]2
[TD=align: center]OFF mode
CH1 controls left track, CH2 controls right track
 
When using triple differential gear box, CH1 controls steering motor, CH2 controls propulsion motor
 


[TD=align: center]Mixer Mode 3
[TD=align: center]3
[TD=align: center]Tank mode 2
CH1 controls rudder, CH2 controls throttle,
Proportional steering and sharp turn are supported
[TABLE=width: 99%]
[TD=colspan: 2, align: center]Left Track
[TD=colspan: 2, align: center]Right Track


[TD=align: center]Sharp
Turn
[TD=align: center]Proportional
Steering
[TD=align: center]Proportional
Steering
[TD=align: center]Sharp
Turn


   


[TD=align: center]Mixer Mode 4
[TD=align: center]4
[TD=align: center]Half-Track mode
CH1 controls rudder, CH2 controls throttle,
Support proportional steering only.
Max. turn ratio ( speed ratio of left and right track at hard left and right turn) can be configured form large (4) to small (8)
[TABLE=width: 99%]
[TD=align: center]Left Track
[TD=align: center]Right Track


[TD=align: center]Proportional
Steering
[TD=align: center]Proportional
Steering



 


[TD=align: center]Mixer Mode 5
[TD=align: center]5


[TD=align: center]Mixer Mode 6
[TD=align: center]6


[TD=align: center]Mixer Mode 7
[TD=align: center]7


[TD=align: center]Mixer Mode 8
[TD=align: center]8



*pivot turn is also named as super spin.
 
Main Gun Function Mode: Press "POWER" key on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]TAMIYA RECOIL MODE*
[TD=align: center]1*
[TD=align: left]To use TAMIYA recoil unit:
CN3, Pin4:TAMIYA Recoil Unit Switch
CN3, Pin5:TAMIYA Recoil Unit Switch
CN9, Pin3:TAMIYA Recoil Unit green Wire
CN9, Pin4:TAMIYA Recoil Unit white Wire


[TD=align: center]HL AirSoft MODE
[TD=align: center]2
[TD=align: left]To use HL AirSoft:
CN3,Pin4:HL AirSoft Unit Switch
CN3,Pin5:HL AirSoft Unit Switch
CN9,Pin3:HL AIRSOFT Motor +
CN9,Pin4:HL AIRSOFT Motor -


[TD=align: center]HL Recoil MODE
[TD=align: center]3
[TD=align: left]To use HL Recoil unit:
CN3,Pin4:HL Recoil Unit Switch
CN3,Pin5:HL Recoil Unit Switch
CN9,Pin3:HL Recoil Motor +
CN9,Pin4:HL Recoil Motor -


[TD=align: center]Gun elevation servo Mode
[TD=align: center]4**
[TD=align: center]For TK22:
CN3,Pin4:NC
CN3,Pin5:NC
CN9,Pin3:AUX POWER +
CN9,Pin4:AUX POWER -
J4.1. Signal( White Wire)
J4.2. +5V ( Red Wire)
J4.3. Battery - (Black Wire)
 
For TK24:
CN3,Pin4:NC
CN3,Pin5:NC
CN9,Pin3:MG2 LED+
CN9,Pin4:MG2 LED+
J4.1. Signal( White Wire)
J4.2. +5V ( Red Wire)
J4.3. Battery - (Black Wire)


*Use this mode on Hooben Tank.
** TK24 default setting
 
Receive TAMIYA IR Code: press "TV/VIDEO" or "->[]" Key on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Enabled
[TD=align: center]1*
[TD=align: center]Tank react to TAMIYA IR code


[TD=align: center]Disabled
[TD=align: center]2
[TD=align: center]


 
Receive HL IR Code: press "VOL DOWN"  Key on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Enabled
[TD=align: center]1*
[TD=align: center]Tank react to HL  IR code,


[TD=align: center]Disabled
[TD=align: center]2
[TD=align: center]


 
IR Battle Preset Data: press  "MTS" or "A/B" Key on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]TAMIYA Heavy tank
[TD=align: center]1*
[TD=align: center]Reload Time = 9 seconds,
Invulnerability time = 10 seconds,
Max. hit can take = 9 hit.


[TD=align: center]TAMIYA Medium tank
[TD=align: center]2
[TD=align: center]Reload Time = 5 seconds,
Invulnerability time = 12 seconds,
Max. hit can take = 6 hits


[TD=align: center]TAMIYA Light  tank
[TD=align: center]3
[TD=align: center]Reload Time = 3 seconds,
Invulnerability time = 15 seconds,
Max. hit can take = 3 hits.


[TD=align: center]Heavy Armored Vehicle
[TD=align: center]4
[TD=align: center]Invulnerability time = 10 seconds,
Max. cannon hit cam take = 1 hit
Max. machine gun hit can take = 24 hit.


[TD=align: center]Medium Armored Vehicle
[TD=align: center]5
[TD=align: center]Invulnerability time = 10 seconds,
Max. cannon hit can take = 1 hit
Max. machine gun hit can take = 16 hit.


[TD=align: center]Light Armored Vehicle
[TD=align: center]6
[TD=align: center]Invulnerability time = 10 seconds,
Max. cannon hit can take = 1 hit
Max. machine gun hit can take = 8 hit.


[TD=align: center]HL tank
[TD=align: center]7
[TD=align: center]Reload Time = 3 seconds,
Invulnerability time = 10 seconds(Note1)
Max. hit can take = 5 hits,


[TD=align: center]Reserved
[TD=align: center]8
[TD=align: center]


Note1: Reference setting for HL Tank
Momentum effect On/Off: Press "SLEEP(0x36)" or "" on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Off
[TD=align: center]1*
[TD=align: center]


[TD=align: center]ON
[TD=align: center]2
[TD=align: center]


*This function is only available on TK22
Reload Sound On/Off: Press "Timer Off(0x3C)" or " "on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]On
[TD=align: center]1*
[TD=align: center]


[TD=align: center]Off
[TD=align: center]2
[TD=align: center]


*This function is only available on TK22
 
Taking a hit hull recoil On/Off: Press "JUMP(0x3B)" on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]On
[TD=align: center]1*
[TD=align: center]


[TD=align: center]Off
[TD=align: center]2
[TD=align: center]


*This function is only available on TK22
 
Strength of taking a hit hull recoil: Press "CH Up" or "PROGR +" key on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]1
[TD=align: center]1
[TD=align: center]Small( 1 ) to Large( 16 )movement


[TD=align: center]:
[TD=align: center]:


[TD=align: center]6
[TD=align: center]6*


[TD=align: center]:
[TD=align: center]:


[TD=align: center]16
[TD=align: center]16


 
Firing tank gun hull recoil On/Off: Press "SURROUND(0x29)" on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]On
[TD=align: center]1*
[TD=align: center]


[TD=align: center]Off
[TD=align: center]2
[TD=align: center]


*This function is only available on TK22
 
Strength of firing tank gun hull recoil: Press "VOL UP" key on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]1
[TD=align: center]1
[TD=align: center]Small( 1 ) to Large( 16 )movement


[TD=align: center]:
[TD=align: center]:


[TD=align: center]6
[TD=align: center]6*


[TD=align: center]:
[TD=align: center]:


[TD=align: center]16
[TD=align: center]16



 
RealRecoil servo direction: press "CH down" or "PROGR -" key on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Normal
[TD=align: center]1*
[TD=align: center]


[TD=align: center]Reversed
[TD=align: center]2
[TD=align: center]


 
Gun elevation servo direction: press " Teletext ON(0x3F)" or "" key on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Normal
[TD=align: center]1*
[TD=align: center]Select this mode if servo controls gun elevation through gear, like our reference design.


[TD=align: center]Reversed
[TD=align: center]2
[TD=align: center]Select this mode if servo controls gun elevation does not through gear, like
TAMIYA Leopard 2


*This function is only available on TK22
 
Speed reduction in damaged state: press "3" key on IR Configuration Remote to select.
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]0%
[TD=align: center]1
[TD=align: center]No mobility damage simulation, Speed is not reduced when Tank is in damaged state.


[TD=align: center]-12.5%
[TD=align: center]2*
[TD=align: center]


[TD=align: center]-25%
[TD=align: center]3
[TD=align: center]


[TD=align: center]-37.5%
[TD=align: center]4
[TD=align: center]


[TD=align: center]-50%
[TD=align: center]5
[TD=align: center]


[TD=align: center]-62.5%
[TD=align: center]6
[TD=align: center]


[TD=align: center]-75%
[TD=align: center]7
[TD=align: center]


[TD=align: center]-87.5%
[TD=align: center]8
[TD=align: center]


 
Speed reduction in badly damaged state: press "DISPLAY" or "DRC-MF" key on IR Configuration Remote to select.
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]0%
[TD=align: center]1
[TD=align: center]No mobility damage simulation, Speed is not reduced when Tank is in badly damaged state.


[TD=align: center]-12.5%
[TD=align: center]2
[TD=align: center]


[TD=align: center]-25%
[TD=align: center]3*
[TD=align: center]


[TD=align: center]-37.5%
[TD=align: center]4
[TD=align: center]


[TD=align: center]-50%
[TD=align: center]5
[TD=align: center]


[TD=align: center]-62.5%
[TD=align: center]6
[TD=align: center]


[TD=align: center]-75%
[TD=align: center]7
[TD=align: center]


[TD=align: center]-87.5%
[TD=align: center]8
[TD=align: center]


 
Armor type: press number key "9" on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Heavy Armor
[TD=align: center]1*
[TD=align: center]Resistance to machine gun


[TD=align: center]Soft skin, like Trucks
[TD=align: center]2
[TD=align: center]No resistance to machine gun


 
Sending IR code when firing  machine gun: press number key "6" on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]Not to send MG IR code
[TD=align: center]1*
[TD=align: center]


[TD=align: center]To send MG IR code
[TD=align: center]2
[TD=align: center]


 
Primary weapon reload time: press number key "4" on IR Configuration Remote to select
[TABLE=width: 639]
[TD=align: center]Available Settings
[TD=align: center]Indicator
flashes times
[TD=align: center]Description


[TD=align: center]3 seconds
[TD=align: center]3
[TD=align: center]


[TD=align: center]4 seconds
[TD=align: center]4
[TD=align: center]


[TD=align: center]5 seconds
[TD=align: center]5
[TD=align: center]


[TD=align: center]6 seconds
[TD=align: center]6
[TD=align: center]


[TD=align: center]7 seconds
[TD=align: center]7
[TD=align: center]


[TD=align: center]8 seconds
[TD=align: center]8
[TD=align: center]


[TD=align: center]9 seconds
[TD=al



Оффлайн Deny

  • Администратор
  • Маршал
  • *****
  • Сообщений: 2131
  • РЕПУТАЦИЯ: +10559/-0
    • Питерский танковод
    • Награды
CLARK
« Ответ #1 : 24 Ноябрь 2016, 17:37:29 »
Так же выкладываю сюда файл пдф на русском по установке кларка


Оффлайн Алекс

  • Клуб
  • Подполковник
  • *
  • Сообщений: 797
  • РЕПУТАЦИЯ: +2862/-0
    • Награды
CLARK
« Ответ #2 : 17 Март 2017, 00:25:54 »
Денис, личка не работает, скинь сюда ссылку на Кларк на и-бее.

Оффлайн Deny

  • Администратор
  • Маршал
  • *****
  • Сообщений: 2131
  • РЕПУТАЦИЯ: +10559/-0
    • Питерский танковод
    • Награды
CLARK
« Ответ #3 : 17 Март 2017, 00:55:42 »

Оффлайн Алекс

  • Клуб
  • Подполковник
  • *
  • Сообщений: 797
  • РЕПУТАЦИЯ: +2862/-0
    • Награды
CLARK
« Ответ #4 : 17 Март 2017, 01:11:03 »
Хорошо, спасибо. А там точно с пультом идет и со светодиодом?

Оффлайн Deny

  • Администратор
  • Маршал
  • *****
  • Сообщений: 2131
  • РЕПУТАЦИЯ: +10559/-0
    • Питерский танковод
    • Награды
CLARK
« Ответ #5 : 17 Март 2017, 01:14:22 »
Почитай все паказано и написано!)))) Алексей, а попробуй в свой профель зайти!

Оффлайн Boggart79

  • Лейтенант
  • **
  • Сообщений: 178
  • РЕПУТАЦИЯ: +1750/-0
    • Награды
CLARK
« Ответ #6 : 17 Март 2017, 09:40:07 »
Леша, а есть ли смысл на ибае кларка покупать?

Оффлайн Deny

  • Администратор
  • Маршал
  • *****
  • Сообщений: 2131
  • РЕПУТАЦИЯ: +10559/-0
    • Питерский танковод
    • Награды
CLARK
« Ответ #7 : 17 Март 2017, 14:12:40 »
Артем, есть!

Оффлайн Юрий_1

  • Клуб
  • Лейтенант
  • *
  • Сообщений: 205
  • РЕПУТАЦИЯ: +1271/-0
    • Награды
Re: CLARK
« Ответ #8 : 12 Февраль 2019, 19:16:51 »
Добрый вечер,
благодаря высокому профессионализму Сергея, удалось подключить универсальную плату для боя (см. соответствующий пост)
к плате Clark и получить универсальный инструмент для ИК боя.
Я доволен полученным результатом и еще раз выражаю Сергею и Денису свою благодарность.
Теперь, наверное, если интересно, осталось выложить фото и написать какие-то слова.
Спасибо.


Оффлайн Алексей Чувашев

  • Клуб
  • Рядовой
  • *
  • Сообщений: 48
  • РЕПУТАЦИЯ: +1/-0
    • Награды
Re: CLARK
« Ответ #9 : 06 Июль 2019, 14:25:50 »
Коллеги помогите приехала плата тк 22 для тигра вроде все подключил , а как приемник и пульт забендить ?